350-401 Exam Dumps Pass with Updated Sep-2025 Tests Dumps
350-401 exam questions for practice in 2025 Updated 378 Questions
To prepare for the Cisco 350-401 exam, candidates can take advantage of various resources provided by Cisco, such as official training courses, study guides, practice exams, and virtual labs. These resources are designed to help candidates acquire the knowledge and skills needed to pass the exam and become proficient in implementing enterprise network solutions.
NEW QUESTION # 184
Which statement about TLS is true when using RESTCONF to write configurations on network devices?
- A. It is used for HTTP and HTTPS requests.
- B. It is not supported on Cisco devices.
- C. It requires certificates for authentication.
- D. It is provided using NGINX acting as a proxy web server.
Answer: D
Explanation:
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/prog/configuration/166/ b_166_programmability_cg/b_166_programmability_cg_chapter_01011.html
NEW QUESTION # 185
Wireless users report frequent disconnections from the wireless network. While troubleshooting a network engineer finds that after the user a disconnect, the connection re-establishes automatically without any input required. The engineer also notices these message logs .
Which action reduces the user impact?
- A. increase the dynamic channel assignment interval
- B. increase the AP heartbeat timeout
- C. increase BandSelect
- D. enable coverage hole detection
Answer: D
Explanation:
Coverage hole detection is a feature in wireless networks that identifies areas where clients have poor signal quality or cannot connect to the network. By enabling this feature, the system can adapt by increasing power levels or making other adjustments to improve coverage, thus reducing the frequency of disconnections for users.
NEW QUESTION # 186
An engineer must construct an access list tot a Cisco Catalyst 9800 Series WLC that will -edirect wireless guest users to a splash page that is hosted on a Cisco ISE server. The Cisco ISE servers are hosted at
10.9.11.141 and 10.1.11.141. Which access list meets the requirements?
- A.
- B.
- C.
- D.
Answer: C
Explanation:
The access list in Option A is specifically designed to prevent wireless guest users from bypassing the splash page by denying IP traffic from the Cisco ISE server addresses (10.9.11.141 and 10.1.11.141) and then permitting TCP traffic on ports typically used for web services (80 and 443). This ensures that users are redirected to the splash page when attempting to access web services.
NEW QUESTION # 187
Refer to the exhibit.
The IP SLA is configured in a router. An engineer must configure an EEM applet to shut down the interface and bring it back up when there is a problem with the IP SLA. Which configuration should the engineer use?
- A. event manager applet EEM_IP_SLA
event sla 10 state down - B. event manager applet EEM_IP_SLA
event sla 10 state unreachable - C. event manager applet EEM_IP_SLA
event track 10 state unreachable - D. event manager applet EEM_IP_SLA
event track 10 state down
Answer: D
Explanation:
Explanation
The ip sla 10 will ping the IP 192.168.10.20 every 3 seconds to make sure the connection is still up. We can configure an EEM applet if there is any problem with this IP SLA via the command event track 10 state down.
NEW QUESTION # 188
Refer to the exhibit.
Object tracking has been configured for VRRP-enabled routers Edge-01 and Edge-02 Which commands cause Edge-02 to preempt Edge-01 in the event that interface G0/0 goes down on Edge-01?
A)
B)
C)
D)
- A. Option D
- B. Option B
- C. Option C
- D. Option A
Answer: D
NEW QUESTION # 189 
Refer to the exhibit. What is the value of the variable list after the code is run?
- A. [1, 2, 10, 4]
- B. [1, 2, 3, 10]
- C. [1, 10, 10, 10]
- D. [1, 2, 10]
Answer: B
NEW QUESTION # 190
Which DNS lookup does an access point perform when attempting CAPWAP discovery?
- A. CISCO-CAPWAP-CONTROLLER.local
- B. CISCO-DNA-CONTROLLER.local
- C. CAPWAP-CONTROLLER.local
- D. CISCO-CONTROLLER.local
Answer: A
Explanation:
Explanation/Reference: http://www.revolutionwifi.net/revolutionwifi/2010/11/capwap-controller-discovery-process_23.html
NEW QUESTION # 191 
Answer:
Explanation:
See the solution below in Explanation:
Explanation:
Solution:
R3
Int e0/1
Ip ospf priority 255
End
Copy run start
R2
Int e0/1
Ip ospf network point-to-point
End
Copy run start
R10
Int e0/0
Ip ospf network point-to-point
End
Copy run start
NEW QUESTION # 192
A customer transitions a wired environment to a Cisco SD-Access solution. The customer does not want to integrate the wireless network with the fabric. Which wireless deployment approach enables the two systems to coexist and meets the customer requirement?
- A. Deploy a separate network for the wireless environment
- B. Implement a Cisco DNA Center to manage the two networks
- C. Deploy the APs in autonomous mode
- D. Deploy the wireless network over the top of the fabric
Answer: D
NEW QUESTION # 193
Which two actions, when applied in the LAN network segment, will facilitate Layer 3 CAPWAP discovery for lightweight AP? Choose two.)
- A. Utilize DHCP option 43.
- B. Utilize DHCP option 17.
- C. Configure WLC IP address LAN switch.
- D. Enable port security on the switch port.
- E. Configure an IP helper-address on the router interface.
Answer: A,E
Explanation:
For Layer 3 CAPWAP discovery of lightweight APs in the LAN network segment, two actions that facilitate this process are:
* Configuring an IP helper-address on the router interface (B): This action helps forward DHCP requests from the APs to the DHCP server, which can then provide the necessary information for the APs to discover the controller.
* Utilizing DHCP option 43 (E): This DHCP option allows the DHCP server to provide the IP address of
* the Wireless LAN Controller (WLC) to the APs, enabling them to discover and join the controller.
NEW QUESTION # 194
An engineer must construct an access list for a Cisco Catalyst 9800 Series WLC that will redirect wireless guest users to a splash page that is hosted on a Cisco ISE server. The Cisco ISE servers are hosted at 10.9.11.141 and 10.1.11.141. Which access list meets the requirements?
- A.
- B.
- C.
- D.
Answer: B
NEW QUESTION # 195
An engineer must configure an ACL that permits packets which include an ACK in the TCP header Which entry must be included in the ACL?
- A. access-list 10 permit tcp any any eq 21 established
- B. access-list 110 permit tcp any any eq 21 established
- C. access-list 10 permit ip any any eq 21 tcp-ack
- D. access-list 110 permit tcp any any eq 21 tcp-ack
Answer: B
Explanation:
The established keyword is only applicable to TCP access list entries to match TCP segments that have the ACK and/or RST control bit set (regardless of the source and destination ports), which assumes that a TCP connection has already been established in one direction only. Let's see an example below:
Suppose you only want to allow the hosts inside your company to telnet to an outside server but not vice versa, you can simply use an "established" access-list like this:
access-list 100 permit tcp any any established
access-list 101 permit tcp any any eq telnet
!
interface S0/0
ip access-group 100 in
ip access-group 101 out
Note: Suppose host A wants to start communicating with host B using TCP. Before they can send real data, a three-way handshake must be established first. Let's see how this process takes place:
1. First host A will send a SYN message (a TCP segment with SYN flag set to 1, SYN is short for SYNchronize) to indicate it wants to setup a connection with host B. This message includes a sequence (SEQ) number for trackingpurpose. This sequence number can be any 32-bit number (range from 0 to 232) so we use
"x" to represent it.
2. After receiving SYN message from host A, host B replies with SYN-ACK message (some books may call it SYN/ACK or SYN, ACK message. ACK is short for ACKnowledge). This message includes a SYN sequence number and an ACK number:
+ SYN sequence number (let's called it "y") is a random number and does not have any relationship with Host A's SYN SEQ number.
+ ACK number is the next number of Host A's SYN sequence number it received, so we represent it with
"x+1. It means I received your part. Now send me the next part (x + 1)".
The SYN-ACK message indicates host B accepts to talk to host A (via ACK part). And ask if host A still wants to talk to it as well (via SYN part).
3. After Host A received the SYN-ACK message from host B, it sends an ACK message with ACK number
"y+1" to host B. This confirms host A still wants to talk to host B.
NEW QUESTION # 196
Which data is properly formatted with JSON?
- A. Option C
- B. Option D
- C. Option A
- D. Option B
Answer: A
NEW QUESTION # 197 
Answer:
Explanation:
See the solution below in Explanation:
Explanation:
Solution:
R30
Config t
router ospf 10
router-id 10.0.1.30
int ran lo0 , e0/0-1
ip ospf 10 a 0
exit
int et0/2
ip ospf 10 a 50
exit
router ospf 10
area 50 range 10.10.0.0 255.255.128.0
area 50 range 10.50.0.0 255.255.128.0
end
NEW QUESTION # 198 
Refer to the exibit. How should the programmer access the list of VLANs that are recevied via the API call?
- A. Option D
- B. Option A
- C. Option C
- D. Option B
Answer: D
Explanation:
To access the list of VLANs received via the API call, the programmer should use the key 'Vlan1' within the VlanNames dictionary. This method allows for direct access to the specific VLAN information required.
References := The explanation is derived from the Implementing and Operating Cisco Service Provider Network Core Technologies training, which covers topics such as networking, automation, and quality of services, relevant to handling VLANs and API calls
NEW QUESTION # 199
Drag and drop the characteristics from the left onto the orchestration tools that they describe on the right.
Answer:
Explanation:
NEW QUESTION # 200
What is the centralized control policy in a Cisco SD-WAN deployment?
- A. set of rules that governs nodes authentication within the cloud
- B. list of enabled services for all nodes within the cloud
- C. set of statements that defines how routing is performed
- D. list of ordered statements that define user access policies
Answer: C
Explanation:
In a Cisco SD-WAN deployment, a centralized control policy is a set of statements that define how routing decisions are made across the network. This policy is centrally managed and distributed to the network devices (vEdges or cEdges) through the SD-WAN controllers. The centralized control policy influences the path selection for data traffic by applying rules that can prioritize, restrict, or modify traffic flows based on various criteria such as application, user, source, destination, and more. It operates on the control plane level, affecting the Overlay Management Protocol (OMP) routes that are distributed by the vSmart controllers throughout the SD-WAN fabric.
References:
* Cisco Catalyst SD-WAN Policies Configuration Guide, Cisco IOS XE Catalyst SD-WAN Release 17.x - Localized Policy [Cisco SD-WAN] - Cisco1.
* Policies Configuration Guide, Cisco IOS XE SD-WAN Releases 16.11, 16.12 - Control Policies [Cisco SD-WAN] - Cisco2.
* What is a Centralized Data Policy? | NetworkAcademy.io
NEW QUESTION # 201
A company requires a wireless solution to support its mam office and multiple branch locations. All sites have local Internet connections and a link to the main office lor corporate connectivity. The branch offices are managed centrally. Which solution should the company choose?
- A. Cisco United Wireless Network
- B. Cisco Mobility Express
- C. Cisco Catalyst switch with embedded controller
- D. Cisco DNA Spaces
Answer: D
NEW QUESTION # 202
If the maximum power level assignment for global TPC 802.11a/n/ac is configured to 10 dBm, which power level effectively doubles the transmit power?
- A. 17dBm
- B. 20 dBm
- C. 13dBm
- D. 14 dBm
Answer: C
Explanation:
Suppose a transmitter is configured for a power level of 10 dBm. A cable with 5-dB loss connects the transmitter to an antenna with an 8-dBi gain. The resulting EIRP of the system is EIRP = 10 dBm - 5 dB + 8 dBi = 13 dBm.
NEW QUESTION # 203
What does this EEM applet event accomplish?
"event snmp oid 1.3.6.1.3.7.1.5.1.2.4.2.9 get-type next entry-op g entry-val 75 poll-interval 5"
- A. It issues email when the value is greater than 75% for five polling cycles.
- B. Upon the value reaching 75%, a SNMP event is generated and sent to the trap server.
- C. It presents a SNMP variable that can be interrogated.
- D. It reads an SNMP variable, and when the value exceeds 75% for live polling cycles.
Answer: D
Explanation:
EEM offers the ability to monitor events and take informational or corrective action when the monitored events occur or reach a threshold. An EEM policy is an entity that defines an event and the actions to be taken when that event occurs. There are two types of EEM policies: an applet or a script. An applet is a simple form of policy that is defined within the CLI configuration.
To specify the event criteria for an Embedded Event Manager (EEM) applet that is run by sampling Simple Network Management Protocol (SNMP) object identifier values, use the event snmp command in applet configuration mode.
event snmp oid oid-value get-type {exact | next} entry-op operator entry-val entryvalue
[exit-comb {or | and}] [exit-op operator] [exit-val exit-value] [exit-time exit-timevalue] poll-interval poll-int-value
+ oid: Specifies the SNMP object identifier (object ID)
+ get-type: Specifies the type of SNMP get operation to be applied to the object ID specified by the oid-value argument.
- next - Retrieves the object ID that is the alphanumeric successor to the object ID specified by the oid-value argument.
+ entry-op: Compares the contents of the current object ID with the entry value using the specified operator. If there is a match, an event is triggered and event monitoring is disabled until the exit criteria are met.
+ entry-val: Specifies the value with which the contents of the current object ID are compared to decide if an SNMP event should be raised.
+ exit-op: Compares the contents of the current object ID with the exit value using the specified operator. If there is a match, an event is triggered and event monitoring is reenabled.
+ poll-interval: Specifies the time interval between consecutive polls (in seconds)
NEW QUESTION # 204
the following system log message is presented after a network administrator configures a GRE tunnel:
%TUN-5-RECURDOWN Interface Tunnel 0 temporarily disabled due to recursive routing Why is tunnel 0 disabled?
- A. Because the tunnel cannot reach its tunnel destination
- B. Because dynamic routing is not enabled
- C. Because the router cannot recursively identify its egress forwarding interface
- D. Because the best path to the tunnel destination is through the tunnel itself
Answer: D
NEW QUESTION # 205
Drag and Drop Question
Drag and drop the snippets onto the blanks within the code to construct a script that adds a prefix list to a route map and sets the local preference. Not all options are used.
Answer:
Explanation:
Explanation:
1. "running": null <<<<target running config
2. "name":"100", <<<<< prefix list name "100"
3. "seq_no": <<<<<<< there is no permit command within a route map. this is the only logical selection here.
4. "match": again within a route map we can either set, or match.
NEW QUESTION # 206
A customer has 20 stores located throughout a city. Each store has a single Cisco AP managed by a central WLC. The customer wants to gather analytics for users in each store. Which technique supports these requirements?
- A. angle of arrival
- B. hyperlocation
- C. trilateration
- D. presence
Answer: D
Explanation:
Explanation
We only have one AP in each store so we can only user "Presence", which is the most basic form of location tracking.
Reference: https://www.ciscolive.com/c/dam/r/ciscolive/emea/docs/2016/pdf/BRKEWN-2012.pdf
NEW QUESTION # 207
......
Cisco 350-401 certification exam, also known as Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR), is designed to assess the knowledge and skills of IT professionals in the implementation and management of enterprise-level networking technologies. 350-401 exam covers a wide range of topics, including network infrastructure, security, automation, and troubleshooting. Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) certification validates the individual's ability to work with complex enterprise networks and implement cutting-edge technologies to improve network performance and security.
Authentic 350-401 Dumps With 100% Passing Rate Practice Tests Dumps: https://validdumps.free4torrent.com/350-401-valid-dumps-torrent.html